Cases2 cases

1 to 2 of 2

1. IL-0133 A storm shut down cooling at Nebius's us-central1 data center, and a disk hot-plug bug kept Managed Kubernetes control planes down for hours after power returned

   Nebius2026

   Symptoms

   On 19 August 2026 the first equipment-level signs in Nebius's us-central1 region appeared around 09:40 UTC: the InfiniBand fabric degraded and GPU over-temperature alerts began to accumulate. Customer reports followed shortly after 10:00. At 10:15 on-call engineers were paged on critical component temperature alerts, and the incident was declared at 10:21.

   Control plane unresponsiveService outageMonitoring outage

   Trigger

   A storm-related event at the data center building took the building management system offline and shut down the chilled-water cooling loop.

   Root cause

   Dependency failure

   Component

   Data center power and coolingCloud block storageetcdInfiniBand fabric

   Contributing factor

   Single point of failureMonitoring blind spotNo alert on limitNo runbookOverlapping failures

   Detection

   No facility-level alert fired, because the storm also disabled the building management system that monitors the facility. Engineers acted on component over-temperature alerts that paged on-call at 10:15 UTC, after InfiniBand degradation, GPU over-temperature alerts and customer reports; the temperature rise from about 09:15 was visible on dashboards but had no alert.

   Remediation

   • had the facility operator switch cooling to manual bypass mode and opened rack rear doors to vent heat
   • re-energised tripped racks, control-plane racks first
   • restored the regional infrastructure control plane by manual intervention
   • restarted block-storage host components to clear stale disk attachment state
   • raised the VM recovery rate limits by hand for the region-scale recovery
   • started the affected Managed Kubernetes control-plane instances by hand
   • applied a controlled stop and start to control-plane instances whose data disk had been left unattached
   • identified and started 104 customer VMs that the incident had stopped

   Action items

   • Complete a joint resilience review with the facility operator covering redundancy of facility-management and monitoring systems, cooling that keeps running when those fail, electrical protection of cooling equipment and on-site response
   • Add facility-level environmental alerting on cooling plant state and room temperature trend that pages on-call independently of the building management system
   • Set up a documented emergency escalation path with the facility operator, with an on-call contact tree and guaranteed response times
   • Define an emergency heat-load reduction procedure with criteria, ownership and mechanics for shutting down or degrading workloads during a cooling loss
   • Establish a dependency-ordered region cold-start procedure with clear ownership for each service layer
   • Run regular region-scale recovery drills that cover VMs, storage attachments and Managed Kubernetes clusters
   • Fix the disk-attachment bug that extended the Managed Kubernetes outage and deploy the fix to all production regions
   • Improve the recovery policies Compute users can configure, and move all Managed Kubernetes control-plane nodes to the improved policy
   • Automate reconciliation of stale storage attachment state after abrupt host failures
   • Remove in-region dependencies from monitoring startup and recovery, and extend cross-region monitoring
   • Make regional health checks used for global traffic management reflect real service availability

   Lessons

   Facility monitoring that runs on the same system it watches goes silent in exactly the failure it should report, and with no alert on the room temperature trend there was no practical window to shed heat load in a controlled way. A cold start of a whole region exercised recovery paths built for isolated failures: single-attempt VM recovery, conservative rate limits and stale disk attachments all needed manual work. The longest part of the outage was restoring customer resources, Managed Kubernetes control planes above all, so Nebius is extending its recovery drills to that layer.

   View case
2. IL-0077 EKS cluster went read-only for over seven hours after Kyverno ephemeralreports filled the etcd database past its size limit

   Marcin Cuber2024sev1

   Symptoms

   A production EKS cluster on Kubernetes 1.30 went into read-only mode: the API server rejected every request that would change an object, such as creating pods or scaling deployments, and deleting objects to free space did not work either.

   Control plane unresponsiveControl plane lag

   Trigger

   Kyverno 1.12 kept creating ephemeralreports objects that piled up in etcd until the database passed EKS's size limit.

   Root cause

   Software defect

   Component

   etcdKubernetes API serverPolicy engine

   Contributing factor

   No alert on limitLimited debug access

   Detection

   The cluster rejected writes; the audit logs carried the "etcdserver: mvcc: database space exceeded" error.

   Remediation

   • AWS raised the etcd storage limit from 8/10GB to 12GB to unlock writes
   • an AWS engineer deleted the leaked Kyverno ephemeralreports objects directly from etcd

   Action items

   • Monitor the etcd database size with apiserver_storage_size_bytes and never let it reach 8GB
   • Upgrade Kyverno 1.12 to 1.12.4, which fixes the ephemeralreports pile-up, or disable reporting for admission events and tune --aggregationWorkers

   Lessons

   On EKS, once etcd hits its size limit the cluster becomes read-only and only AWS can clean it up, so cleanup scripts must run before the limit is reached. Watch the etcd database size and object counts per resource, especially for controllers that create report objects.

   View case

By root cause2