Cases2 cases

1 to 2 of 2

1. IL-0085 A control plane node of Magic Pages' Kubernetes cluster on Hetzner Cloud ran out of memory, the cluster's own calls then used up the Hetzner API rate limit, and all customer websites were down for about 7.5 hours

   Magic Pages2025

   Symptoms

   At around 09:33 UTC one of the three control plane nodes of the Kubernetes cluster that hosts Magic Pages went offline. Looking at the node showed that it had run out of memory.

   Service outageNode NotReadyCloud API rate limit exhausted

   Trigger

   One of the three control plane nodes ran out of memory and went offline at about 09:33 UTC; the attempts to replace it with hetzner-k3s failed while the cluster's own components were exhausting the Hetzner API rate limit.

   Root cause

   Capacity exhaustion

   Component

   Cloud controller managerPersistent volumes and stateful sets

   Contributing factor

   Unknown limitRetry stormMonitoring blind spotLimited debug accessSingle point of failureNo runbook

   Detection

   The founder found the control plane node offline at about 09:33 UTC. Monitoring alerts about unreachable customer websites started around the time the replacement attempts failed, and about half an hour of investigation identified the exhausted Hetzner API rate limit.

   Remediation

   • powered off all servers of the Kubernetes cluster to stop the API requests so the Hetzner rate limit could recover
   • waited until ratelimit-remaining had built up a buffer before starting recovery
   • restarted the control plane servers
   • started the essential Longhorn components by hand so Longhorn could heal and make storage volumes available
   • restarted the remaining websites by hand

   Action items

   • Monitor the Hetzner API call rate coming from the Kubernetes cluster nodes themselves to get early warning of high usage
   • Get a higher Hetzner API rate limit; Hetzner support was contacted
   • Investigate how to reduce the cluster's reliance on a single API, including alternatives to hetzner-k3s
   • Document and test a procedure for recovering Longhorn after a full cluster shutdown

   Lessons

   The running cluster, not only the deployment tooling, consumed the cloud provider's API quota, and in a failure it consumed it fast enough that the quota never recovered. The default limit of 3600 requests per hour was not enough for failure and recovery scenarios, and API usage from inside the cluster was not monitored. A tool that hides the provider's API errors slows diagnosis. After a full, non-graceful shutdown, Longhorn needed manual intervention to come back, which lengthened the outage.

   View case
2. IL-0153 DOKS worker nodes went NotReady at 06:00 UTC on three days because a systemd timer in the Debian image ran apt upgrade and killed it mid kernel upgrade, breaking node networking

   DigitalOcean2023

   Symptoms

   Customers of DigitalOcean Managed Kubernetes (DOKS) saw worker nodes go NotReady between 06:00 and 07:00 UTC and stay unavailable, taking down the services on them, until the nodes were replaced or rebooted; some nodes needed several replacements or reboots. The first sporadic reports on October 8 said replacing the node fixed it. The same thing happened again around 06:00 UTC on October 9, more widely and across many regions, and again on October 10. Only clusters on versions 1.27.6-do.0 and 1.28.2-do.0 were affected.

   Node NotReadyService outage

   Trigger

   A systemd timer in the DigitalOcean Debian image started apt upgrade daily at 06:00 UTC, with a random delay of up to 60 minutes.

   Root cause

   Configuration change

   Component

   Node operating system imageLinux kernelkubelet

   Contributing factor

   Unreviewed defaultsLimited debug accessChange with a delayed effect

   Detection

   Sporadic customer reports of failed worker nodes arrived at 07:43 UTC on October 8; internal incident response started at 07:10 UTC on October 9 after broader impact across regions.

   Remediation

   • Advised customers to replace or reboot affected worker nodes
   • Arranged SSH and console access to worker nodes while they were healthy, and live-debugged an affected node on October 10
   • Released a DaemonSet to all affected clusters that disables the apt upgrade systemd timer on every worker node
   • Released new node images without the auto-update process

   Action items

   • Disable the timer during node provisioning, then remove the DaemonSet from all clusters
   • Add a check to the internal conformance test suite for new cluster versions that the auto-upgrade process and other unwanted timers stay disabled
   • Support logging into worker nodes even when normal access paths are broken

   Lessons

   An operating system auto-update timer left enabled in a node image can change the kernel and systemd underneath Kubernetes, and a timeout that kills the upgrade half-way can leave a node without networking. Failures that start at the same time every day point to a scheduled job on the nodes, and systemd timers belong on that list next to cron jobs. When the failure takes out a node's network, an investigation that depends on logging into the node stalls; access paths that work while the node is broken shorten diagnosis.

   View case

By root cause2