Cases18 cases

6 to 10 of 18

1. IL-0150 A latent race condition in DynamoDB's DNS automation left an empty DNS record for dynamodb.us-east-1.amazonaws.com, and the DynamoDB and EC2 launch failures that followed caused EKS, ECS and Fargate container launch failures and cluster scaling delays in us-east-1

   Amazon Web Services2025

   Symptoms

   At 11:48 PM PDT on 19 October 2025, every system that reached DynamoDB in us-east-1 through the public regional endpoint started getting DNS failures and could not connect. This included customer traffic and internal AWS services that depend on DynamoDB. DynamoDB global table replicas in other regions still answered but fell behind in replication to and from us-east-1.

   DNS resolution failuresHigh error rateScale-up failureIntermittent connection failuresHigh latency

   Trigger

   One DNS Enactor, slowed by unusually high retry delays, applied a much older DNS plan to the regional DynamoDB endpoint just as another Enactor that had applied the newest plan ran its clean-up, which deleted that older plan and with it every IP address of the endpoint.

   Root cause

   Software defect

   Component

   Authoritative DNS servers and recordsDatabaseCloud load balancer

   Contributing factor

   Automation amplificationRetry stormNo runbook

   Detection

   DNS failures to DynamoDB began immediately at 11:48 PM PDT and the engineering teams of affected AWS services were engaged at once; by 12:38 AM they had identified DynamoDB's DNS state as the source. The later NLB health check problem was detected by monitoring at 6:52 AM.

   Remediation

   • applied temporary mitigations by 1:15 AM that let some internal services reach DynamoDB and repaired key internal tooling
   • restored all DynamoDB DNS information by 2:25 AM through manual operator intervention
   • throttled incoming work and selectively restarted DWFM hosts from 4:14 AM so droplet leases could be re-established
   • reduced the load on Network Manager to bring network configuration propagation times back to normal by 10:36 AM
   • disabled automatic health check failover for NLB at 9:36 AM, and re-enabled it at 2:09 PM after EC2 recovered
   • relaxed the EC2 request throttles from 11:23 AM until all EC2 APIs and launches were normal at 1:50 PM

   Action items

   • Disable the DynamoDB DNS Planner and DNS Enactor automation worldwide
   • Fix the race condition and add protections against applying incorrect DNS plans before re-enabling the DNS automation
   • Add a velocity control to NLB that limits how much capacity a single load balancer can remove when health check failures cause availability zone failover
   • Build an additional EC2 test suite that exercises the DWFM recovery workflow at scale
   • Improve throttling in EC2 data propagation systems so incoming work is rate limited by the size of the waiting queue

   Lessons

   A single DNS record that automation can empty is enough to take a widely used regional endpoint off the network, and every service built on it fails in turn. A check made once at the start of a long operation can be stale by the time the operation writes its result. Recovery of the dependency is not recovery of the dependents: systems that lost state during the outage, such as EC2's droplet leases and network propagation backlog, can collapse under their own catch-up work, and container services that rely on new instance launches keep failing to launch and scale until that work is done.

   View case
2. IL-0006 VPC subnets ran out of IP addresses because the AWS VPC CNI kept IPs on full nodes, and WARM_IP_TARGET changes then blocked pod starts after every pod deletion

   Neon2025

   Symptoms

   On 16 May 2025, in Neon's Kubernetes cluster in AWS us-east-1, new compute pods were scheduled but could not start and failed with IP allocation errors. Each Neon compute is a Postgres database running in a lightweight virtual machine in its own pod, so without new pods, idle customer databases could not be woken up.

   IP address exhaustionPods Pending

   Trigger

   On 16 May the Neon control plane's periodic job that terminates idle computes started failing. Compute creations continued, and the number of active computes rose from about 5k to about 8.1k within minutes. On 19 May, a follow-up change that set WARM_IP_TARGET back to 1 started the second round of failures.

   Root cause

   Capacity exhaustion

   Component

   AWS VPC CNIVPC subnet or pod address rangeCluster autoscaler

   Contributing factor

   Unreviewed defaultsNo capacity planningUnverified assumptionHarmful manual actionIneffective rollbackRetry storm

   Detection

   As cluster-autoscaler added nodes, the team saw IP allocation errors on new pods that were scheduled but could not start. The rate of successful pod starts and VPC subnet metrics were then used to follow the problem.

   Remediation

   • Set WARM_IP_TARGET=1 to release IPs held by nodes without free CPU or memory
   • Fixed the control plane's periodic job so idle computes were terminated again
   • Restarted the aws-node DaemonSet several times, each with a temporary improvement
   • Set WARM_IP_TARGET=0, MINIMUM_IP_TARGET=0 and WARM_ENI_TARGET=0, which let nodes allocate enough IPs and stabilised the cluster
   • On 19 May, set WARM_IP_TARGET back to 0 after setting it to 1 failed again
   • Enlarged the pool of pre-created warm compute pods to absorb failed pod starts

   Action items

   • Open a pull request to AWS CNI to improve how ipamd releases IPs in this situation
   • Follow up with AWS Support about the roughly 100 subnet IPs that were never allocated, for reasons Neon could not explain
   • Change the architecture to support horizontal scaling

   Lessons

   With default settings AWS CNI can keep many IPs on nodes that cannot use them, so the share of subnet IPs assigned to pods does not tell how close the subnet is to running out. WARM_IP_TARGET and WARM_ENI_TARGET follow different logic, a warm IP target of zero switches to the ENI logic, and IPs in cooldown count toward the target, which behaves badly under high pod churn. Changing these settings during an incident without knowing that logic prolonged the outage, and reverting a setting did not bring back the earlier healthy state.

   View case
3. IL-0085 A control plane node of Magic Pages' Kubernetes cluster on Hetzner Cloud ran out of memory, the cluster's own calls then used up the Hetzner API rate limit, and all customer websites were down for about 7.5 hours

   Magic Pages2025

   Symptoms

   At around 09:33 UTC one of the three control plane nodes of the Kubernetes cluster that hosts Magic Pages went offline. Looking at the node showed that it had run out of memory.

   Service outageNode NotReadyCloud API rate limit exhausted

   Trigger

   One of the three control plane nodes ran out of memory and went offline at about 09:33 UTC; the attempts to replace it with hetzner-k3s failed while the cluster's own components were exhausting the Hetzner API rate limit.

   Root cause

   Capacity exhaustion

   Component

   Cloud controller managerPersistent volumes and stateful sets

   Contributing factor

   Unknown limitRetry stormMonitoring blind spotLimited debug accessSingle point of failureNo runbook

   Detection

   The founder found the control plane node offline at about 09:33 UTC. Monitoring alerts about unreachable customer websites started around the time the replacement attempts failed, and about half an hour of investigation identified the exhausted Hetzner API rate limit.

   Remediation

   • powered off all servers of the Kubernetes cluster to stop the API requests so the Hetzner rate limit could recover
   • waited until ratelimit-remaining had built up a buffer before starting recovery
   • restarted the control plane servers
   • started the essential Longhorn components by hand so Longhorn could heal and make storage volumes available
   • restarted the remaining websites by hand

   Action items

   • Monitor the Hetzner API call rate coming from the Kubernetes cluster nodes themselves to get early warning of high usage
   • Get a higher Hetzner API rate limit; Hetzner support was contacted
   • Investigate how to reduce the cluster's reliance on a single API, including alternatives to hetzner-k3s
   • Document and test a procedure for recovering Longhorn after a full cluster shutdown

   Lessons

   The running cluster, not only the deployment tooling, consumed the cloud provider's API quota, and in a failure it consumed it fast enough that the quota never recovered. The default limit of 3600 requests per hour was not enough for failure and recovery scenarios, and API usage from inside the cluster was not monitored. A tool that hides the provider's API errors slows diagnosis. After a full, non-graceful shutdown, Longhorn needed manual intervention to come back, which lengthened the outage.

   View case
4. IL-0542 Twingate authentication and authorization requests failed at higher rates after traffic moved onto a smaller GKE cluster

   Twingate2025

   Symptoms

   On 21 March 2025, between 21:10 and 21:41 UTC, part of the authentication and authorization requests to Twingate services failed with elevated error rates.

   High error rate

   Trigger

   Twingate saw anomalies in one of its GKE clusters and scaled down the deployments in that cluster to protect the rest of the system, which moved its traffic to the other clusters.

   Root cause

   Cloud provider outage

   Component

   Cloud load balancerGKE control planeHorizontal pod autoscalerCluster autoscaler

   Contributing factor

   Retry stormNo headroomOverlapping failuresHarmful manual action

   Detection

   Twingate observed anomalies in one of its GKE clusters at the start of the incident.

   Remediation

   • Reintroduced capacity in the cluster that had been scaled down, so traffic was rebalanced across regions

   Action items

   • Keep working with the cloud provider to find the cause of the unexpected timeouts and of the cluster update's impact
   • Run deployments in all regions with the same number of replicas in the HPA configuration
   • Raise the maximum node counts of the cluster node autoscalers to leave more room to scale up
   • Configure the HPA to scale up faster

   View case
5. IL-0168 Simultaneous cluster auto-upgrades overloaded Scaleway's Kubernetes API, and a node authentication retry loop kept Kapsule and Kosmos nodes NotReady in FR-PAR

   Scaleway2024

   Symptoms

   At 01:04 CET on 13 February 2024, the Kubernetes API behind Scaleway's managed Kubernetes services Kapsule and Kosmos in the Paris region (FR-PAR) spiked in RAM and CPU use and ran out of memory. Nodes in FR-PAR could no longer authenticate to their control plane, and some of them went "Not Ready". Customers on both shared (mutualized) and dedicated environments were affected.

   Node NotReadyControl plane lagOOMKilled

   Trigger

   A new Kubernetes release was made available to all users on 12 February 2024, and during the night of 12 to 13 February many clusters triggered their auto-upgrade at the same time.

   Root cause

   Capacity exhaustion

   Component

   Kubernetes API server

   Contributing factor

   Retry stormAutomation amplificationNo staged rollout

   Detection

   The timeline's first entry, at 01:04 CET, records the Kubernetes API's RAM and CPU spikes and out-of-memory state, with nodes unable to authenticate to their control plane and some becoming "Not Ready". The first recorded action, 42 minutes later at 01:46, was to increase the resources allocated to the API.

   Remediation

   • increased the resources allocated to the Kubernetes API at 01:46 and again at 02:20
   • applied API traffic restrictions at 02:30 to smooth the incoming traffic
   • removed the traffic restrictions progressively in 50-100 batches from 03:20
   • ran a script at 03:40 to replace the failing nodes created during the congestion
   • rolled back to the former node authentication mechanism, first on a subset of clusters from 15:45 and on all clusters by 19:41 on 19 February
   • disabled cluster upgrade and configuration update features until 10:30 on 20 February

   Action items

   • Increase the resources allocated to the Kubernetes API
   • Roll back to the former node authentication mechanism
   • Implement a local authentication cache on nodes
   • Rework the resource allocation strategy to behave better under load spikes
   • Add new request queuing mechanisms for Kubernetes
   • Separate the different components to reduce side effects under high load or failure
   • Monitor selected metrics closely to identify anomalous patterns earlier
   • Refund customers who deployed nodes during the incident but could not use them normally

   Lessons

   Letting many clusters auto-upgrade at the same moment after a release turns routine upgrades into one coordinated load spike on the shared Kubernetes API. A node authentication mechanism that retries without letting up turns a slow API into an unavailable one, and auto-healing that replaces NotReady nodes amplifies the problem. The congestion pattern had already appeared three weeks earlier, and short-term mitigations did not stop it from recurring, so Scaleway rolled back the new authentication mechanism. Scaleway notes that as the number of customer clusters and nodes grows sharply, traffic control mechanisms have to improve to prevent congestion.

   View case

By root cause4