Cases6 cases

3 to 6 of 6

1. IL-0202 A burst of queries and database writes exhausted connection pools and memory on Honeycomb's ingest hosts, and Kubernetes crash-loop back-off kept failed hosts offline so ingest capacity stayed too low to recover

   Honeycomb2023sev1

   Symptoms

   Standard alerting paged Honeycomb's on-call engineers about the performance and stability of event ingestion, and the automated load-shedding mechanisms tripped and sent further notifications. The status page described a higher than normal error rate and response time on the ingestion service.

   High error rateHigh latencyContainer crash loopService outageDatabase overload

   Trigger

   An abnormally large number of queries arrived from many separate connections within a few minutes.

   Root cause

   Capacity exhaustion

   Component

   Application databaseIn-memory cache

   Contributing factor

   Retry stormAutomation amplification

   Detection

   Standard alerting notified the on-call engineers about ingestion performance and stability, and the automated load-shedding mechanisms added notifications when they tripped. The first status post, about alerts on a higher than normal error rate and response time, went up at 18:28 PST (02:28 UTC), 13 minutes after the 02:15 UTC start.

   Remediation

   • Scaled the ingest fleet up manually and aggressively
   • Cut off most ingest for a few minutes so the ingest hosts could come back with enough capacity
   • Temporarily lowered the rate limits for the most aggressive traffic sources until their traffic subsided

   Action items

   • Keep the ingest fleet scaled up to prevent a repeat while longer-term fixes are worked on
   • Decide on the projects that will address these failure paths

   Lessons

   Load shedding and auto-scaling were in place, yet a burst that arrived faster than the cache could spread its writes still took the ingest hosts down. During recovery, Kubernetes' crash loop back-off worked against the operators: the hosts that had failed stayed offline while the fleet needed every host. Clients that retry whole OTel batches after a partial drop can multiply traffic many times over, so per-source rate limits were what finally stabilised ingest.

   View case
2. IL-0206 Consul agents in GitLab.com's GKE pods were repeatedly OOM-killed, so the Rails pods lost database replica discovery and sent every query to the primary

   GitLab2022

   Symptoms

   On 2022-04-25 the Sidekiq Apdex (the share of background jobs that finish within a target time) dropped, and an engineer declared an incident in Slack at 15:13 UTC. Users saw intermittent slowness across GitLab.com, and asynchronous work such as pipeline creation and import and export took unusually long.

   High latencyDatabase overloadOOMKilledHigh error rate

   Trigger

   The Consul agent in GitLab.com's GKE pods had memory demand spikes that did not fit in the pods' 500MB memory limit, and the agent was killed again and again.

   Root cause

   Capacity exhaustion

   Component

   Container memory limitService discoveryApplication database

   Contributing factor

   –

   Detection

   An engineer declared the incident in Slack at 15:13 UTC after the Sidekiq Apdex dropped; the second event was found when monitoring detected an elevated error rate at 01:21 UTC on 2022-04-26.

   Remediation

   • planned at 16:13 to raise the per-user connection limit for the gitlab database user and the pgbouncer backend pools for the main database; changes were applied at 17:26 and confirmed at 17:47
   • raised the pod memory limits from 500MB to 1GB so the Consul agents survive memory spikes

   Action items

   • Monitor the Consul agents on GKE pods to see whether the 1GB memory limit keeps them healthy
   • Investigate the Consul memory demand spikes and what can be done beyond raising the hard memory limit

   Lessons

   When the local Consul agent that Rails uses for database service discovery keeps dying, Rails does not fail; it sends every query to the last known primary. What engineers saw was database saturation and slow background jobs, which pointed the investigation first at a recent pgbouncer pool change. The memory limit of the Consul agent in every pod therefore decided the load on the primary database.

   View case
3. IL-0037 Image registry rate-limited a whole region after a crash-looping DaemonSet with imagePullPolicy Always pulled through three NAT instances

   Datadog2019

   Symptoms

   Users reported that their jobs were not starting, with some sign that image pulls were involved. Many pods across the cluster were in error states related to image pulls, while applications that were already running were not affected.

   Image pull failuresService outage

   Trigger

   A change to the permissions on a storage bucket that one application needed to read. The application could no longer start, and its DaemonSet, running on roughly a thousand nodes of the cluster, went into a crash loop with imagePullPolicy: Always, so every restart pulled the image again although it was already on the node.

   Root cause

   Capacity exhaustion

   Component

   Container registry and its credentialsNAT gatewayApplication databaseAdmission webhook

   Contributing factor

   Automation amplificationSingle point of failureUnknown limitHarmful manual actionExcessive blast radius

   Detection

   Users reported that their jobs were not starting; monitoring had not caught it first.

   Remediation

   • replaced the affected NAT instances so registry traffic came from new source IPs
   • reconfigured the static IPs and firewall rules so applications could reach the Cloud SQL database again

   Action items

   • Add an admission webhook that rejects floating image tags, starting with latest
   • Apply the image tag webhook to workload objects only, not to pods, after it blocked pods created by in-cluster controllers

   Lessons

   The speakers' takeaway is to be very careful with DaemonSets in large clusters: they say they had broken everything DaemonSets depend on, including DNS, Vault and the image repository, and that it is very easy to break things when managing them by the thousand. imagePullPolicy: Always made every crash-loop restart pull the image again. Sending all registry traffic through three NAT instances put the whole region behind three source IPs, which the registry rate-limited, and changing those IPs cut the connections to a critical database reached over the internet through them. An admission webhook on pods rejects the pods that controllers in the cluster create, where no user sees the error.

   View case
4. IL-0064 CPU-heavy pods packed onto one Google Cloud node drove it to kernel panics, and the crash moved from node to node until the site was down

   Moonlight2019

   Symptoms

   On Friday, January 18, Moonlight's API began returning occasional errors that looked like connection problems with its Redis database. The API checks Redis on every authenticated request to validate the session. At the same time the Kubernetes monitoring reported some nodes and pods as unresponsive.

   High error rateIntermittent connection failuresNode NotReadyService outageSustained high node CPU

   Trigger

   The Kubernetes scheduler put several CPU-heavy pods on the same node, including all three replicas of the website and the server-side rendering pods.

   Root cause

   Capacity exhaustion

   Component

   Pod scheduling and placementLinux kernelApplication database

   Contributing factor

   Single point of failureUnverified assumptionAutomation amplification

   Detection

   API errors that looked like Redis connectivity problems, and Kubernetes monitoring that showed nodes and pods as unresponsive. Google Cloud Support later found the link between sustained 100% CPU and kernel panics.

   Remediation

   • added anti-affinity rules to all major deployments so their pods spread across nodes

   Action items

   • Keep working with Google Cloud support to find and fix the cause of the node kernel panics

   Lessons

   Three replicas give no fault tolerance if the scheduler places them all on one node; anti-affinity rules make the spread explicit. A node failure that comes from the workload itself moves with the workload when the scheduler reschedules it.

   View case

By root cause1