Cases8 cases

1 to 5 of 8

1. IL-0438 Builder Work became almost entirely unreachable with 504 errors when the Amazon CloudFront VPC Origins feature failed

   ANDPAD2026

   Symptoms

   At about 17:00 JST on Thursday 16 July 2026, Datadog alerted, and at almost the same time 5xx errors began to rise on the Amazon CloudFront distributions that used VPC Origins connections. Builder Work, ANDPAD's job and career service for the construction industry, became almost entirely unreachable.

   Service outageHigh error rate

   Trigger

   The Amazon CloudFront VPC Origins feature failed; AWS Health later reported a capacity constraint in an internal shared subsystem that manages connections for VPC Origins.

   Root cause

   Cloud provider outage

   Component

   CDN and edge networkCloud load balancerIngress controllerWeb application firewall rules

   Contributing factor

   Single point of failure

   Detection

   Datadog raised an alert, and at about the same time 5xx errors were seen rising on the CloudFront distributions that used VPC Origins.

   Remediation

   • Decided to route traffic temporarily through an internet-facing ALB without CloudFront
   • Recreated the internet-facing Ingress, attached it to the Argo Rollouts Rollout resource and promoted it
   • Created a regional WAF for the ALB with the security team
   • Created a new IngressClass with the ACM certificate, the WAF and access log settings
   • Added Ingresses for normal traffic, the admin screens and redirects, which restored routing

   Action items

   • Return to the CloudFront and VPC Origins layout while keeping a way to switch to internet-facing in code
   • Keep the internet-facing ALB, limited to approved CIDRs through spec.inboundCIDRs in IngressClassParams, so commenting out securityGroupInboundCidrs in values.yaml opens it to 0.0.0.0/0
   • Point the Terraform-managed Route53 A record back to CloudFront and keep the ALB alias commented out in code, so uncommenting and applying switches DNS to the ALB

   Lessons

   VPC Origins keeps the ALB off the internet and simplifies the traffic path, but it makes the service depend on an AWS-managed shared subsystem, and when that fails the service stops even though CloudFront is healthy. ANDPAD kept VPC Origins and instead prepared the escape route ahead of time, accepting the cost of an ALB that always runs, because recreating the Ingress and attaching it to the Rollout had taken so long during this incident.

   View case
2. IL-0188 Rolling updates on EKS returned 502 errors for about 30 seconds because Kubernetes deleted old pods as soon as new pods passed readiness, before the ALB had marked the new pod targets healthy

   Yonghyun Kim2025

   Symptoms

   Every rolling update of the team's microservices on Amazon EKS, behind an Application Load Balancer, was followed by intermittent 502 and 503 errors for users. A Slack message at 3 a.m. read "배포는 성공했는데, 서비스는 죽었다" (the deployment succeeded, but the service died). Every pod was Ready and Datadog was green while users saw errors.

   High error rateService outage

   Trigger

   A rolling update of a Deployment served through an ALB that registers pod IPs as targets, with no pod readiness gates.

   Root cause

   Faulty deployment

   Component

   Cloud load balancerIngress controllerPod termination

   Contributing factor

   Unverified assumptionUnreviewed defaultsMonitoring blind spot

   Detection

   A Slack message at 3 a.m. reported that the deployment had succeeded but the service was down; Datadog dashboards were green at the time.

   Remediation

   • labelled the namespace with elbv2.k8s.aws/pod-readiness-gate-inject=enabled so the AWS Load Balancer Controller injects pod readiness gates and Kubernetes waits for the ALB target to be healthy before deleting old pods

   Lessons

   A pod being Ready in Kubernetes does not mean the load balancer will send it traffic. Without a readiness gate, a rolling update can delete the old pods while the ALB still considers the new targets unhealthy, and dashboards that track pod status stay green during the errors. Making pods wait longer on shutdown reduced the errors but did not fix the start-up gap and made every deployment much slower; the readiness gate ties the pod's Ready state to the ALB's view of the target.

   View case
3. IL-0150 A latent race condition in DynamoDB's DNS automation left an empty DNS record for dynamodb.us-east-1.amazonaws.com, and the DynamoDB and EC2 launch failures that followed caused EKS, ECS and Fargate container launch failures and cluster scaling delays in us-east-1

   Amazon Web Services2025

   Symptoms

   At 11:48 PM PDT on 19 October 2025, every system that reached DynamoDB in us-east-1 through the public regional endpoint started getting DNS failures and could not connect. This included customer traffic and internal AWS services that depend on DynamoDB. DynamoDB global table replicas in other regions still answered but fell behind in replication to and from us-east-1.

   DNS resolution failuresHigh error rateScale-up failureIntermittent connection failuresHigh latency

   Trigger

   One DNS Enactor, slowed by unusually high retry delays, applied a much older DNS plan to the regional DynamoDB endpoint just as another Enactor that had applied the newest plan ran its clean-up, which deleted that older plan and with it every IP address of the endpoint.

   Root cause

   Software defect

   Component

   Authoritative DNS servers and recordsDatabaseCloud load balancer

   Contributing factor

   Automation amplificationRetry stormNo runbook

   Detection

   DNS failures to DynamoDB began immediately at 11:48 PM PDT and the engineering teams of affected AWS services were engaged at once; by 12:38 AM they had identified DynamoDB's DNS state as the source. The later NLB health check problem was detected by monitoring at 6:52 AM.

   Remediation

   • applied temporary mitigations by 1:15 AM that let some internal services reach DynamoDB and repaired key internal tooling
   • restored all DynamoDB DNS information by 2:25 AM through manual operator intervention
   • throttled incoming work and selectively restarted DWFM hosts from 4:14 AM so droplet leases could be re-established
   • reduced the load on Network Manager to bring network configuration propagation times back to normal by 10:36 AM
   • disabled automatic health check failover for NLB at 9:36 AM, and re-enabled it at 2:09 PM after EC2 recovered
   • relaxed the EC2 request throttles from 11:23 AM until all EC2 APIs and launches were normal at 1:50 PM

   Action items

   • Disable the DynamoDB DNS Planner and DNS Enactor automation worldwide
   • Fix the race condition and add protections against applying incorrect DNS plans before re-enabling the DNS automation
   • Add a velocity control to NLB that limits how much capacity a single load balancer can remove when health check failures cause availability zone failover
   • Build an additional EC2 test suite that exercises the DWFM recovery workflow at scale
   • Improve throttling in EC2 data propagation systems so incoming work is rate limited by the size of the waiting queue

   Lessons

   A single DNS record that automation can empty is enough to take a widely used regional endpoint off the network, and every service built on it fails in turn. A check made once at the start of a long operation can be stale by the time the operation writes its result. Recovery of the dependency is not recovery of the dependents: systems that lost state during the outage, such as EC2's droplet leases and network propagation backlog, can collapse under their own catch-up work, and container services that rely on new instance launches keep failing to launch and scale until that work is done.

   View case
4. IL-0542 Twingate authentication and authorization requests failed at higher rates after traffic moved onto a smaller GKE cluster

   Twingate2025

   Symptoms

   On 21 March 2025, between 21:10 and 21:41 UTC, part of the authentication and authorization requests to Twingate services failed with elevated error rates.

   High error rate

   Trigger

   Twingate saw anomalies in one of its GKE clusters and scaled down the deployments in that cluster to protect the rest of the system, which moved its traffic to the other clusters.

   Root cause

   Cloud provider outage

   Component

   Cloud load balancerGKE control planeHorizontal pod autoscalerCluster autoscaler

   Contributing factor

   Retry stormNo headroomOverlapping failuresHarmful manual action

   Detection

   Twingate observed anomalies in one of its GKE clusters at the start of the incident.

   Remediation

   • Reintroduced capacity in the cluster that had been scaled down, so traffic was rebalanced across regions

   Action items

   • Keep working with the cloud provider to find the cause of the unexpected timeouts and of the cluster update's impact
   • Run deployments in all regions with the same number of replicas in the HPA configuration
   • Raise the maximum node counts of the cluster node autoscalers to leave more room to scale up
   • Configure the HPA to scale up faster

   View case
5. IL-0178 On EKS, HPA scale-in returned 502 errors because containers stopped before their pod IPs left the Service endpoints, and after blue/green switches conntrack kept sending established connections to deleted pods behind an instance-mode ALB

   Lotte E-commerce2022

   Symptoms

   LOTTE ON, Lotte E-commerce's online shopping mall of about 40 microservices on Amazon EKS, returned errors for a period of time whenever the Horizontal Pod Autoscaler (HPA) scaled pods in after load dropped. Requests reached containers that had already been deleted and failed with 502 errors.

   High error rateIntermittent timeoutsStale endpoint routing

   Trigger

   HPA scale-in deleting pods, and the deletion of Blue pods after a blue/green switch of the Service label selector.

   Root cause

   DNS or network fault

   Component

   Horizontal pod autoscalerPod terminationkube-proxyconntrack tableCloud load balancerIngress controller

   Contributing factor

   Unreviewed defaults

   Remediation

   • delayed container shutdown on pod deletion (a wait in the SIGTERM handler or a preStop sleep, capped by terminationGracePeriodSeconds) so containers stop only after the pod has left the Service endpoints
   • switched some workloads' Ingress-created ALBs from instance mode to IP mode so traffic goes straight to pod IPs without iptables and conntrack

   Action items

   • Move all workloads to ALB IP mode gradually

   Lessons

   Removing a pod from Service endpoints and stopping its containers happen at the same time in Kubernetes, so a pod can stop while traffic is still routed to it unless shutdown is delayed with a preStop hook or in the application. With an instance-mode ALB, traffic passes through node iptables and conntrack, and established connections can keep going to a pod IP after its iptables rules are gone. IP mode avoids that path, within the limit of 1000 targets per target group.

   View case

By root cause5