Cases2 cases

1 to 2 of 2

1. IL-0085 A control plane node of Magic Pages' Kubernetes cluster on Hetzner Cloud ran out of memory, the cluster's own calls then used up the Hetzner API rate limit, and all customer websites were down for about 7.5 hours

   Magic Pages2025

   Symptoms

   At around 09:33 UTC one of the three control plane nodes of the Kubernetes cluster that hosts Magic Pages went offline. Looking at the node showed that it had run out of memory.

   Service outageNode NotReadyCloud API rate limit exhausted

   Trigger

   One of the three control plane nodes ran out of memory and went offline at about 09:33 UTC; the attempts to replace it with hetzner-k3s failed while the cluster's own components were exhausting the Hetzner API rate limit.

   Root cause

   Capacity exhaustion

   Component

   Cloud controller managerPersistent volumes and stateful sets

   Contributing factor

   Unknown limitRetry stormMonitoring blind spotLimited debug accessSingle point of failureNo runbook

   Detection

   The founder found the control plane node offline at about 09:33 UTC. Monitoring alerts about unreachable customer websites started around the time the replacement attempts failed, and about half an hour of investigation identified the exhausted Hetzner API rate limit.

   Remediation

   • powered off all servers of the Kubernetes cluster to stop the API requests so the Hetzner rate limit could recover
   • waited until ratelimit-remaining had built up a buffer before starting recovery
   • restarted the control plane servers
   • started the essential Longhorn components by hand so Longhorn could heal and make storage volumes available
   • restarted the remaining websites by hand

   Action items

   • Monitor the Hetzner API call rate coming from the Kubernetes cluster nodes themselves to get early warning of high usage
   • Get a higher Hetzner API rate limit; Hetzner support was contacted
   • Investigate how to reduce the cluster's reliance on a single API, including alternatives to hetzner-k3s
   • Document and test a procedure for recovering Longhorn after a full cluster shutdown

   Lessons

   The running cluster, not only the deployment tooling, consumed the cloud provider's API quota, and in a failure it consumed it fast enough that the quota never recovered. The default limit of 3600 requests per hour was not enough for failure and recovery scenarios, and API usage from inside the cluster was not monitored. A tool that hides the provider's API errors slows diagnosis. After a full, non-graceful shutdown, Longhorn needed manual intervention to come back, which lengthened the outage.

   View case
2. IL-0076 Kubernetes masters went down after Dex filled etcd with AuthRequest objects and deleting its namespace started an endless list-and-timeout loop

   Fullstaq2019

   Symptoms

   Dex, the OIDC proxy that handled Kubernetes authentication, stored its data in the Kubernetes API (storage type kubernetes, inCluster: true) and had built up a huge number of AuthRequest objects. Listing all AuthRequests timed out, and without the list they could not be deleted.

   Control plane unresponsiveMonitoring outage

   Trigger

   The dex namespace was deleted so that Kubernetes would clean up the accumulated AuthRequest objects itself.

   Root cause

   Capacity exhaustion

   Component

   Kubernetes API serveretcdCluster authentication provider

   Contributing factor

   Unreviewed defaultsHarmful manual actionRetry stormLimited debug accessIgnored early signal

   Detection

   The speaker says he had got hints of the problem earlier. While the masters were down, plenty of alerts arrived in Slack, but monitoring could not be reached because authentication and port-forwarding no longer worked.

   Remediation

   • removed the kubernetes finalizer from the dex namespace by calling the API directly (kill-kube-ns)
   • deployed Dex to a new namespace with sane defaults

   Lessons

   Dex with Kubernetes as its storage keeps every AuthRequest as an API object, and with a long TTL they pile up until the API cannot list them. Deleting a namespace that holds that many objects makes Kubernetes list them in a loop and can overload the masters. Monitoring that is reached through cluster authentication is lost when authentication is what broke.

   View case

By root cause1