Cases71 cases

16 to 20 of 71

1. IL-0085 A control plane node of Magic Pages' Kubernetes cluster on Hetzner Cloud ran out of memory, the cluster's own calls then used up the Hetzner API rate limit, and all customer websites were down for about 7.5 hours

   Magic Pages2025

   Symptoms

   At around 09:33 UTC one of the three control plane nodes of the Kubernetes cluster that hosts Magic Pages went offline. Looking at the node showed that it had run out of memory.

   Service outageNode NotReadyCloud API rate limit exhausted

   Trigger

   One of the three control plane nodes ran out of memory and went offline at about 09:33 UTC; the attempts to replace it with hetzner-k3s failed while the cluster's own components were exhausting the Hetzner API rate limit.

   Root cause

   Capacity exhaustion

   Component

   Cloud controller managerPersistent volumes and stateful sets

   Contributing factor

   Unknown limitRetry stormMonitoring blind spotLimited debug accessSingle point of failureNo runbook

   Detection

   The founder found the control plane node offline at about 09:33 UTC. Monitoring alerts about unreachable customer websites started around the time the replacement attempts failed, and about half an hour of investigation identified the exhausted Hetzner API rate limit.

   Remediation

   • powered off all servers of the Kubernetes cluster to stop the API requests so the Hetzner rate limit could recover
   • waited until ratelimit-remaining had built up a buffer before starting recovery
   • restarted the control plane servers
   • started the essential Longhorn components by hand so Longhorn could heal and make storage volumes available
   • restarted the remaining websites by hand

   Action items

   • Monitor the Hetzner API call rate coming from the Kubernetes cluster nodes themselves to get early warning of high usage
   • Get a higher Hetzner API rate limit; Hetzner support was contacted
   • Investigate how to reduce the cluster's reliance on a single API, including alternatives to hetzner-k3s
   • Document and test a procedure for recovering Longhorn after a full cluster shutdown

   Lessons

   The running cluster, not only the deployment tooling, consumed the cloud provider's API quota, and in a failure it consumed it fast enough that the quota never recovered. The default limit of 3600 requests per hour was not enough for failure and recovery scenarios, and API usage from inside the cluster was not monitored. A tool that hides the provider's API errors slows diagnosis. After a full, non-graceful shutdown, Longhorn needed manual intervention to come back, which lengthened the outage.

   View case
2. IL-0020 During an EKS 1.30 upgrade the descheduler tried to reschedule every pod on the cordoned nodes at once and production workloads went down

   UK Ministry of Justice2025

   Symptoms

   At 09:36 on 18 March 2025, during the upgrade of the live cluster to EKS 1.30, users reported that their pods were being terminated and were not restarting automatically, in both production and non-production environments. Automated infrastructure alerts fired as well, and production services had outages.

   Pod evictionPods PendingService outageUpgrade stall

   Trigger

   Upgrading the live EKS cluster from 1.29 to 1.30, during which the descheduler attempted to reschedule all pods on the cordoned nodes simultaneously.

   Root cause

   Faulty deployment

   Component

   DeschedulerNode poolCluster autoscaler

   Contributing factor

   No headroomNo alert on limitUnreviewed defaults

   Detection

   Users reported at 09:36 that pods were being terminated and not restarting, and automated infrastructure alerts fired.

   Remediation

   • Removed the cordon annotation so pods could be rescheduled
   • Deleted stuck 1.30 nodes to force their recreation
   • Added a new node group of 20 nodes running 1.30 by hand
   • Cordoned and drained all old 1.29 nodes onto the new 1.30 nodes

   Action items

   • Raise an AWS Production System Down support case (Case ID: 174229643100496)
   • Get guidance from AWS support on querying control-plane logs to find the root cause of similar issues
   • Document a runbook for emergency scaling of a new node group in case of unexpected capacity shortages
   • Alert on an imbalance between the autoscaling group and the Kubernetes nodes
   • Review the descheduler configuration to understand why it throws pods off cordoned nodes, and fix it where possible
   • Alert on spikes in the pending pod count

   Lessons

   The write-up lists review actions rather than lessons. They show the team had no documented way to add an emergency node group, no alert on a mismatch between the autoscaling group and the nodes Kubernetes sees, no alert on a spike in pending pods, and no clear understanding of how the descheduler treats cordoned nodes.

   View case
3. IL-0157 After a release, new nodes could not join Linode Kubernetes Engine clusters with IP ACL enabled, so autoscaling failed on about 20 to 25 clusters

   Linode2025

   Symptoms

   From about 01:00 UTC on 2025-03-05, Linode Kubernetes Engine (LKE) clusters with IP ACL enabled failed to autoscale: new nodes could not join the cluster, and some customers had service disruptions. About 20 to 25 clusters in several regions around the world were affected; the status page lists the US-IAD (Washington), US-ORD (Chicago), US-SEA (Seattle) and IN-MAA (Chennai) LKE components.

   Scale-up failureService outage

   Trigger

   Akamai deployed the latest LKE software release.

   Root cause

   Software defect

   Component

   Cluster autoscaler

   Contributing factor

   –

   Detection

   Customers began having problems at about 01:00 UTC, and the first status post, at 06:49 UTC, said the team was investigating an LKE autoscaling problem when IP ACL is turned on.

   Remediation

   • restarted the gateway pods, which gave only short-term relief
   • rolled back the release on all affected clusters

   Action items

   • Continue investigating the root cause and take preventive actions

   Lessons

   The defect hit only clusters with IP ACL enabled, and it showed when the autoscaler tried to add nodes. Restarting the gateway pods did not hold; rolling back the release ended the incident.

   View case
4. IL-0138 A failed Nvidia driver build left broken kernel packages on the only Kubernetes master node, which hit a kernel panic on reboot after a power outage and took the homelab cluster down for six days

   Barush Mendez2025

   Symptoms

   Every service in the homelab Kubernetes cluster stopped answering: the V-Rising server, Grafana, Jellyfin and Linkding were all unreachable, and the Kubernetes API was down, so the cluster could not be managed at all. The outage was found by hand, about 3 hours after it began, when someone tried to use the services.

   Control plane unresponsiveService outageMonitoring outage

   Trigger

   A power outage forced the Kubernetes master node to reboot.

   Root cause

   Software defect

   Component

   GPU driverLinux kernelKubernetes API server

   Contributing factor

   Ignored early signalChange with a delayed effectSingle point of failureMonitoring blind spot

   Detection

   Manually, when someone tried to access the services; there were no automated alerts.

   Remediation

   • Connected a monitor to the master node and read the boot logs, which showed the kernel panic
   • Booted the previous kernel version, which brought the system back
   • Removed the broken Nvidia packages with sudo apt-get remove --purge '^nvidia-.*' and ran sudo dpkg --configure -a
   • Found remaining broken packages with dpkg -l | grep -v ^ii and removed them by hand
   • Ran sudo apt-get install -f and reinstalled linux-headers-$(uname -r)
   • Rebooted and confirmed the kernel panic was gone

   Action items

   • Make sure GPU driver installations fully succeed, or revert immediately when they fail
   • Move the cluster to a high-availability control plane
   • Expose the Kubernetes API through a load balancer in the HA setup
   • Set up a ticketing system to record incidents and their resolution
   • Write predefined troubleshooting workflows to shorten response time
   • Add infrastructure monitoring such as Prometheus and Grafana
   • Add blackbox HTTP and TCP checks from outside the cluster for critical services

   Lessons

   A driver installation that fails half-way can leave kernel packages broken without any visible effect until the next reboot, which may come weeks later and at the worst time. A failed DKMS build should be fixed or reverted at once. With a single master node and no monitoring from outside the cluster, one unbootable machine meant a total outage that nobody was told about; the fix itself was simple once the boot logs were seen.

   View case
5. IL-0192 A Crossplane composition merge-policy change for a TLS policy update switched Kubernetes Services from LoadBalancer to ClusterIP and deleted the load balancers behind about 25% of Grafana Cloud services

   Grafana Labs2025

   Symptoms

   At 08:41 UTC on 18 February 2025, several Grafana Labs application teams noticed that some of their endpoints were no longer available. The investigation quickly found that the load balancers for those endpoints were gone.

   Service outageResources deleted

   Trigger

   A change to the merge policy of a Crossplane composition, made so that the default TLS policy of the load balancers could be overridden, was applied to development, staging and production at the same time.

   Root cause

   Configuration change

   Component

   Configuration templatingCloud load balancer

   Contributing factor

   Unverified assumptionNo staged rolloutExcessive blast radiusNo safeguard on destructive change

   Detection

   Application teams noticed at 08:41 UTC that some of their endpoints were no longer available.

   Remediation

   • rolled back the Crossplane composition change
   • recreated the affected Kubernetes Services so that Kubernetes recreated their load balancers

   Action items

   • Add a CI check that blocks a deployment to more than one wave, so any exception to the dev, staging, canary, production order is caught
   • Give higher priority to a more sophisticated wave design that was already under discussion
   • Enable deletion protection on the load balancers, one layer below Crossplane
   • Enable deletion protection on other critical cloud provider resources
   • Develop the Crossplane Managed Resources exporter for change validation and visibility, now in beta testing within Platform engineering; simulated against the change that caused this outage, it shows a clear diff
   • Complete and test support for reconfiguring the TLS policy so application teams can deploy it

   Lessons

   A change that looked small and low-risk had a side effect that only a full end-to-end test through Crossplane and the cloud provider's load balancer controller would have shown; seeing the intended override work was not that test. Staged rollout and blast-radius limits that exist only as process can be skipped, so Grafana Labs moved to enforce waves in CI and to add deletion protection on the load balancers themselves, beneath the Crossplane layer.

   View case

By root cause11