Cases36 cases

4 to 8 of 36

1. IL-0063 VPN outage after recreating a Redis StatefulSet restarted the whole Redis cluster without readiness checks

   AdGuard VPN2025

   Symptoms

   The day began with an alert that several instances of the Redis cluster were running out of disk space. That part was fixed quickly. The outage came an hour later: right after the Redis StatefulSet was deleted and recreated at 8:10 UTC, Kubernetes restarted every Redis pod within about five minutes, and problems started to appear.

   Service outageOOMKilledProbe failuresHigh latency

   Trigger

   To make Git match the volumes that had been resized by hand, the Redis StatefulSet was deleted with orphan (non-cascading) deletion and recreated with the new storage template; Kubernetes reconciled the new spec by restarting the entire Redis cluster.

   Root cause

   Configuration change

   Component

   Persistent volumes and stateful setsIn-memory cacheContainer memory limit

   Contributing factor

   No health probesUnverified assumptionSingle point of failureRetry stormNo headroom

   Detection

   An alert about Redis instances running out of disk space started the work; the outage itself showed up as backend errors about Redis connections right after the StatefulSet was recreated.

   Remediation

   • made the Redis masters forget obsolete node identities, reset the affected replicas and rejoined them, then waited for replication to catch up
   • identified the component that was actually running out of memory, scaled the backend service and raised memory limits for that component
   • temporarily relaxed probes so backend instances took traffic immediately instead of flapping between ready and not ready
   • reverted the temporary workarounds at 10:00 UTC

   Action items

   • Add startup probes so a Redis pod is not marked ready until its dataset is loaded
   • Build an own control plane for Redis that handles restarted pods stuck to an old master address
   • Reduce dependence on the single Redis cluster: move some important data to other stores, such as a separate Redis cluster per server, and use Kafka for some backend components

   Lessons

   The disk resize was not the problem; the cleanup afterwards was. An immutable field pushes operators toward deleting and recreating the controller, and that can set off a full reconcile. Startup and readiness probes are what slow a rolling restart down to a safe pace; without them a distributed store restarts in the most fragile way. Recovery plans must expect a cluster to heal slowly, and dependent services need to degrade gracefully while it does.

   View case
2. IL-0100 PostHog's feature flags pods were packed onto Kubernetes nodes that were too small for their CPU requests, and CPU saturation above 90% caused three outages in ten days through Redis overload, connection pool exhaustion and slow queries

   PostHog2025

   Symptoms

   On 21 October 2025 at 21:45 UTC a change to timeout handling was deployed to the feature flags service, and two minutes later automated monitoring reported higher error rates. The change was rolled back by 21:49, but error rates stayed high: about 38% of flag evaluation requests in the US datacenter returned errors. At 22:30 Redis metrics showed memory exhaustion on ElastiCache, at 22:35 Postgres connections spiked, and at 22:45 the team found a massive data transfer from Postgres into Redis. The main PostHog application was affected as well, because it shares the Redis instance with the flags service.

   Sustained high node CPUHigh error rateHigh latencyContainer crash loopDatabase overload

   Trigger

   On 21 October a deployment meant to reduce timeout errors (PR #39821); on 24 October the deployment of IP-based rate limiting (PR #40074) that saw all traffic as coming from the load balancer's IP; on 28 October an unrelated routine deployment that rolled the feature flag pods in the US region.

   Root cause

   Capacity exhaustion

   Component

   Node poolPod scheduling and placementIn-memory cacheApplication database

   Contributing factor

   No alert on limitRetry stormIneffective rollbackSingle point of failureNo staged rolloutUnrepresentative staging

   Detection

   On 21 October automated monitoring detected higher error rates two minutes after the deploy. On 24 October no alert existed for 429 errors, and the team learned of the incident from customer reports that began at 18:10 UTC, a 62-minute detection delay. On 28 October on-call received a high error count alert. On 29 October the incident was reported with higher error rates and latency. No alert existed for CPU pressure, so the CPU saturation behind all three incidents was not seen directly.

   Remediation

   • rolled back the timeout handling change within 2 minutes on 21 October, which did not stop the errors
   • throttled connections and Redis writes on 21 October
   • halted the rollout on 28 October, scaled the US flags pods to zero until Redis recovered, then scaled them back gradually
   • rolled back hardware changes on 30 October at 00:03 UTC, which removed most errors but not the latency
   • increased the pod resource requests and adjusted the Kubernetes fleet size so fewer pods ran on each node
   • added retry limits to Envoy between the load balancer and the service
   • moved database connection timeouts and other critical settings to runtime configuration and raised the timeout values
   • added per-node and per-pod CPU alerts at 80% sustained for 5 minutes that page on-call

   Action items

   • Form a strike team from the flags, ingestion and infrastructure teams to review the application and infrastructure for remaining bottlenecks
   • Investigate separating the flags Redis instance from the application Redis instance
   • Before re-enabling ArgoCD sync, align the flags service chart configuration with the values in ArgoCD and define the deployment and Redis strategy
   • Make the feature flags team hard code-owners for flags-related code
   • Build a dashboard of key flag metrics with runbook links and update the feature flag runbooks
   • Add missing alerts on existing service and infrastructure metrics
   • Make readiness checks validate dependencies that degrade under load, for example by pinging the database
   • Rate-limit cache population so it cannot overwhelm Redis
   • Monitor connection pools with automatic throttling near exhaustion and limit concurrent connections
   • Build a production-scale load testing framework
   • Build progressive rollout infrastructure to limit blast radius
   • Document Postgres-to-Redis data flows and write runbooks for data transfer storms

   Lessons

   Nodes that are small relative to pod requests let the scheduler pack many pods on each node, and the resulting CPU saturation showed up three different ways: excessive parallelism, connection pool exhaustion and slow queries. Treating each symptom separately let the problem return; right-sizing the pods and nodes fixed all three. CPU must be alerted on from the start. Unbounded Envoy retries and unbounded cache population amplified the overload, and a Redis instance shared with the main application spread a flags problem to the main application. A rollback did not end the incident, because the data transfer and resource exhaustion it had started kept running.

   View case
3. IL-0150 A latent race condition in DynamoDB's DNS automation left an empty DNS record for dynamodb.us-east-1.amazonaws.com, and the DynamoDB and EC2 launch failures that followed caused EKS, ECS and Fargate container launch failures and cluster scaling delays in us-east-1

   Amazon Web Services2025

   Symptoms

   At 11:48 PM PDT on 19 October 2025, every system that reached DynamoDB in us-east-1 through the public regional endpoint started getting DNS failures and could not connect. This included customer traffic and internal AWS services that depend on DynamoDB. DynamoDB global table replicas in other regions still answered but fell behind in replication to and from us-east-1.

   DNS resolution failuresHigh error rateScale-up failureIntermittent connection failuresHigh latency

   Trigger

   One DNS Enactor, slowed by unusually high retry delays, applied a much older DNS plan to the regional DynamoDB endpoint just as another Enactor that had applied the newest plan ran its clean-up, which deleted that older plan and with it every IP address of the endpoint.

   Root cause

   Software defect

   Component

   Authoritative DNS servers and recordsApplication databaseCloud load balancer

   Contributing factor

   Automation amplificationRetry stormNo runbook

   Detection

   DNS failures to DynamoDB began immediately at 11:48 PM PDT and the engineering teams of affected AWS services were engaged at once; by 12:38 AM they had identified DynamoDB's DNS state as the source. The later NLB health check problem was detected by monitoring at 6:52 AM.

   Remediation

   • applied temporary mitigations by 1:15 AM that let some internal services reach DynamoDB and repaired key internal tooling
   • restored all DynamoDB DNS information by 2:25 AM through manual operator intervention
   • throttled incoming work and selectively restarted DWFM hosts from 4:14 AM so droplet leases could be re-established
   • reduced the load on Network Manager to bring network configuration propagation times back to normal by 10:36 AM
   • disabled automatic health check failover for NLB at 9:36 AM, and re-enabled it at 2:09 PM after EC2 recovered
   • relaxed the EC2 request throttles from 11:23 AM until all EC2 APIs and launches were normal at 1:50 PM

   Action items

   • Disable the DynamoDB DNS Planner and DNS Enactor automation worldwide
   • Fix the race condition and add protections against applying incorrect DNS plans before re-enabling the DNS automation
   • Add a velocity control to NLB that limits how much capacity a single load balancer can remove when health check failures cause availability zone failover
   • Build an additional EC2 test suite that exercises the DWFM recovery workflow at scale
   • Improve throttling in EC2 data propagation systems so incoming work is rate limited by the size of the waiting queue

   Lessons

   A single DNS record that automation can empty is enough to take a widely used regional endpoint off the network, and every service built on it fails in turn. A check made once at the start of a long operation can be stale by the time the operation writes its result. Recovery of the dependency is not recovery of the dependents: systems that lost state during the outage, such as EC2's droplet leases and network propagation backlog, can collapse under their own catch-up work, and container services that rely on new instance launches keep failing to launch and scale until that work is done.

   View case
4. IL-0082 Losing one CoreDNS pod during a planned EKS node reroll overloaded the remaining CoreDNS pods, causing DNS timeouts and errors across multiple services at RebelMouse

   RebelMouse2025

   Symptoms

   At 13:42 UTC on 19 May 2025, RebelMouse's monitoring tools reported a higher error rate and degraded performance across services. A routine reroll of the EKS nodes had started 27 minutes earlier, at 13:15 UTC.

   DNS resolution failuresHigh latencyHigh error rateService outage

   Trigger

   At 13:15 UTC RebelMouse started its regular reroll of EKS nodes to apply security patches. The planned, automatic termination of an EC2 instance terminated one of the CoreDNS pods.

   Root cause

   Capacity exhaustion

   Component

   CoreDNSNode pool

   Contributing factor

   Change during peak hours

   Detection

   Monitoring tools detected an increased error rate and degraded service performance at 13:42 UTC, and the tech team started investigating at 13:44 UTC.

   Remediation

   • rescheduled the affected CoreDNS pod onto a new EC2 instance
   • scaled up the CoreDNS deployment to more replicas so DNS load was spread evenly across all pods

   Action items

   • Add scale-in protection so CoreDNS pods are not terminated unexpectedly during peak load
   • Review the CoreDNS configuration so that vertical scaling of the pods works
   • Hold regular capacity reviews so the CoreDNS deployment is provisioned for peak load

   View case
5. IL-0027 All CoreDNS pods landed on one node, the node ran out of memory, and DNS for the whole service went down

   Backpackr2025

   Symptoms

   Services on the production Amazon EKS cluster behind the idus marketplace threw intermittent errors whose cause was hard to pin down. Calls to external services such as RDS and Redis failed now and then, and whenever DNS traffic spiked, domain lookups answered slowly or failed outright.

   DNS resolution failuresIntermittent connection failuresHigh latencyOOMKilledService outage

   Trigger

   All CoreDNS pods were scheduled onto the same node, and that node's memory usage spiked until it ran out of memory.

   Root cause

   Capacity exhaustion

   Component

   CoreDNSClient-side DNS resolver and cachekubeletContainer memory limitNode pool

   Contributing factor

   Unreviewed defaultsSingle point of failureNo caching

   Detection

   The write-up does not say how the full outage was noticed. The earlier DNS trouble showed up as intermittent service errors, and investigating failed calls to RDS and Redis led to DNS resolution failures.

   Remediation

   • deployed NodeLocal DNSCache as a DaemonSet in front of CoreDNS
   • added a PodDisruptionBudget (maxUnavailable 1) and topologySpreadConstraints across zones for CoreDNS
   • lowered ndots from 5 to 2 with dnsConfig in the Deployments

   Lessons

   The CoreDNS setup that EKS creates by default (two pods) can be enough for a small or development cluster but becomes a bottleneck in a large production cluster, and DNS is a single point of failure that needs high availability and room to scale. Tuning the CoreDNS cache and buffer size only relieved the symptoms; the real load came from the extra queries that ndots:5 generates for external names. A CoreDNS pod without a memory limit can share a node's fate with everything else on it.

   View case

By root cause7